CareerExamPro

Construction Documentation, NCIDQ Interiors & AICP/LARE Planning practice questions

20 questions from the NCARB ARE 5.0, NCIDQ, AICP & LARE practice test.

Start practising

Construction Documentation, NCIDQ Interiors & AICP/LARE Planning practice drill

10 realistic exam questions, graded as you go, with the exact rule or statute citation for every answer. Start free, no sign-up.

Sample questions

In a Project Manual organized under CSI MasterFormat, where are bidding instructions, the owner-contractor agreement, and general conditions located versus administrative procedures such as submittal workflows, temporary utilities, and closeout procedures?

  1. Both bidding rules and submittals belong in Division 00 outside the technical documents.
  2. Procurement and contracting documents belong in Division 00; administrative and procedural requirements belong in Division 01.
  3. Bidding instructions belong in Division 01, while submittals and temporary utilities belong in Division 02.
  4. General conditions and agreement forms belong in Division 01, while Division 00 is reserved for project-specific supplemental drawings and addenda.
Show the answer

B. Procurement and contracting documents belong in Division 00; administrative and procedural requirements belong in Division 01.

Under CSI MasterFormat, Division 00 (Procurement and Contracting Requirements) contains solicitation documents, instructions to bidders, bid forms, the owner-contractor agreement, bonds, and General/Supplementary Conditions. Division 01 (General Requirements) is the first division of the Specifications and governs administrative and procedural work rules that apply across all technical divisions—including summary of work, submittal procedures, quality requirements, temporary facilities, and project closeout.

Reference: CSI Project Resource Manual (PRM) / CSI MasterFormat Divisions 00 & 01

While coordinating a commercial tenant build-out specification under CSI MasterFormat, an architect must assign (1) elastomeric joint sealants and fluid-applied air barriers, (2) hollow metal frames, glazing, and door hardware, and (3) gypsum board assemblies and acoustical panel ceilings. Which division mapping is correct?

  1. Division 06 for sealants and air barriers, Division 07 for door hardware and glazing, and Division 08 for gypsum board and ceilings.
  2. Division 05 for hollow metal frames, Division 07 for gypsum board and sealants, and Division 09 for glass glazing and architectural hardware.
  3. Division 07 for glazing and door hardware, Division 08 for air barriers and roofing, and Division 09 for gypsum board and exterior cladding.
  4. Division 07 for sealants/air barriers, Division 08 for frames/glazing/hardware, and Division 09 for gypsum/ceilings.
Show the answer

D. Division 07 for sealants/air barriers, Division 08 for frames/glazing/hardware, and Division 09 for gypsum/ceilings.

In CSI MasterFormat: Division 07 (Thermal and Moisture Protection) covers waterproofing, air barriers, insulation, roofing, flashing, firestopping, and joint sealants; Division 08 (Openings) covers doors, hollow metal/aluminum frames, windows, curtain walls, glazing, and door hardware; and Division 09 (Finishes) covers gypsum board, plaster, tile, acoustical ceilings, resilient flooring, carpeting, and painting/coatings.

Reference: CSI MasterFormat (Divisions 07, 08 & 09) / Architectural Graphic Standards

Where should a low-permeance vapor retarder be positioned in a wood-framed exterior wall in a cold, heating-dominated climate (ASHRAE Climate Zone 6) compared to a hot-humid, cooling-dominated climate (ASHRAE Climate Zone 1A)?

  1. On the warm-in-winter interior side in Zone 6, and toward the exterior side (avoiding interior vinyl wallcoverings) in Zone 1A.
  2. On the exterior cold side behind cladding in Zone 6 to block rain, and directly behind interior gypsum board in Zone 1A to trap cooled air.
  3. On both the interior and exterior faces of the stud cavity in both climates to create a doubly sealed assembly against bidirectional diffusion.
  4. Centered inside the fiberglass batt insulation in Zone 6, and omitted from all roof and slab assemblies in Zone 1A.
Show the answer

A. On the warm-in-winter interior side in Zone 6, and toward the exterior side (avoiding interior vinyl wallcoverings) in Zone 1A.

Water vapor diffuses from the warm, high-vapor-pressure side toward the cold, low-vapor-pressure side. In a cold heating-dominated climate (Zone 6), winter vapor drive is outward, so a vapor retarder goes on the warm-in-winter (interior) side (or exterior continuous insulation keeps the sheathing warm). In a hot-humid climate (Zone 1A), vapor drive is inward toward air-conditioned interiors, so low-permeance layers belong toward the exterior—and interior vapor barriers (such as vinyl wallcoverings) must be avoided to prevent condensation and mold behind the finish. Double vapor barriers trap moisture and prevent drying.

Reference: IBC 2021/2024 Section 1404.3 (Vapor Retarders) / Building Science Corporation (BSD-106)

Other topics